發新話題
打印

[轉貼]VGA显示线如何焊接

[轉貼]VGA显示线如何焊接

http://blog.jianghu.taobao.com/u/MTcxODkwMDI=/blog/blog_detail.htm?aid=25044076

 

VGA显示线如何焊接

公头背面焊接点的顺序

uploads/200804/12_155918_20080130_72cd65fbf7b82e5d121afouygsuxfstd.jpg


一、15针VGA各针脚的定义:
按照VGA接头(15HD)的标准,共各引脚的定义如下:(PIN表示“脚”的意思)
1PIN ——Red——模拟信号的“红”
2PIN ——Green——模拟信号的“绿”
3PIN ——Blue——模拟信号的“蓝”
4PIN ——ID Bit 、
5PIN ——N/C 、
6PIN ——R.GND——模拟信号的“红”的接地端
7PIN ——G.GND——模拟信号的“绿”的接地端
8PIN ——B.GND ——模拟信号的“蓝”的接地端
9PIN ——No.Pin 、(备用)
10PIN——GND ——数子信号的的接地端
11PIN——ID Bit——屏幕与主机之间的控制或地址码
12PIN——ID Bit ——屏幕与主机之间的控制或地址码(用于一个主机多个显示屏)
13PIN——H Sync—— 数字的水平行场信号
14PIN——V Sync ——数字的垂直行场信号
15PIN——N/C——接地端

uploads/200804/12_155918_20080130_72cd65fbf7b82e5d121afouygsuxfstd.jpg

二、标准15针 VGA头焊接方法:
标准15针 VGA 头的各针脚如下图显示(3+4 线型,3表示3根同轴红、绿、蓝,4表示4根黑、棕、黄、白线) VGA的脚通常按照倒梯形来看,从上到下,从左到右分别是1-5脚,6-10脚,11——15脚;(注意 D15 接头一定选用金属外壳)如下图所示:
15针脚我们通常只需要焊接11个引脚即可,如下:(4、5、9、12脚不焊)
红线——“1”脚——模拟信号的“红”;
绿线——“2”脚——模拟信号的“绿”;
蓝线——“3”脚——模拟信号的“蓝”;
红线外屏蔽线——“6”脚——模拟信号的“红”的接地屏蔽线;
绿线外屏蔽线——“7”脚——模拟信号的“绿”的接地屏蔽线;
蓝线外屏蔽线——“8”脚——模拟信号的“蓝”的接地屏蔽线;
黑线——“10”脚——数子信号的的接地端;

棕线——“11”脚——屏幕与主机之间的控制或地址码;

黄线——“13”脚——数字的水平“行”同步信号;
白线——“14”脚——数子信号的垂直“场”同步信号;
VGA 线外屏蔽线——“15”脚——VGA插座外壳压接接地 。
在实际工程中,经常会在地线的连接中出现错误,如果将某些脚(如4,5,9,15等)接到地线上,在大屏显示不出什么问题;但如10脚未接地的话,就会出现地线不通而出问题。有些设备将不用的引脚全部接地了,虽然不标准,但挺实用,只是如果要用到相应的控制位时会出问题。

uploads/200804/12_155918_20080130_72cd65fbf7b82e5d121afouygsuxfstd.jpg

三、VGA针脚只焊7线的焊接方法:(如用网线中的8芯焊接)
第一、 1 、 2 、 3 脚 分别用网线中的三根线(1-橙,2-绿,3-蓝)记着两边颜色对应;

第二、 5~10 脚 焊接在一起做公共地;用8根网线中的某一根颜色的线(在此我们记作用“橙白”色线),记着两头都用这根颜色的线,6、7、8脚针焊在一起接到公共地上;
第三、 11脚 接网线中的某个线(在此定义为接棕色线,11-棕)
第四、 13脚 接网线中的某根颜色的线(在此定义用绿白线,13-绿白);
第五、 14脚 接网线中的某根颜色的线(在此定义用绿白线,14-蓝白);
第六、15脚 VGA插座外壳压接接地,(在此定义用绿白线,15-棕白)
15号针脚其实应该跟5-10脚焊一起都当作地线,这样实际上就是焊7针脚了。

如果用专用VGA线缆涂简便只焊7针脚的话焊接方法就是:就是在 D15 两端的 5~10 脚焊接在一起做公共地;红、绿、蓝的屏蔽线绞在一起接到公共地上; 1 、 2 、 3 脚接红、绿、蓝的芯线; 13 接黄线; 14 接白线; 外层屏蔽压接到 D15插头端壳,褐线和黑线不用接,但是要剪齐,以防和其他线串接。



四、VGA线缆布放和施工中注意的问题:
1、线缆选用:一般工程和家庭中最好购买专门的VGA线缆,价格层次不齐,中等可用的大概价:格6-10元/米,低于6元/米的可能不怎么样,高于13元/米的应该算是质量很好的。如果实在没条件购买的话就用别的凑乎了,比如用网线,用网线距离最好不要超过10-15米,5米左右还可以,再长图像效果不行。
VGA线缆的7根线:专用VGA线缆中有7根线,外带屏蔽层当作1根线,7根线中有红、蓝、绿各一根,注意这三根中每根都是带有屏蔽层的细同轴线,所以这3根线实际上就是6根针脚了,黑、棕、黄、白线各一根。所以买到线后不要惊讶怎么里边只有7根线而不是11根或者15根呢,如果看了这个还不知道那就是勺了啊。
2、布线距离:单段VGA线缆标准要求的距离是不要超过15米,但我们平时应用没那么严格,因为我们对图像要求没那么高,在正常情况下用到40米图像也还都可以。超过40米或者图像不怎么行的时候就要加VGA放大器了。用网线或者其他不带屏蔽的线缆最好不要超过15米。通常我们想一台电脑上的图像放到多台显示器或者电脑上,那你就去电脑城买个VGA分配器,价格大概在60元左右。
3、干扰问题:图像不清楚或者有干扰大概是信号不好或者有干扰,布线不要跟音箱喇叭线布一起,那个线的干扰很大的。焊头子是要焊好,不要搞的毛毛草草的。如果头子靠近电源插座或者电源插板,最好拿个什么铁盒子把接头处屏蔽一下子或许起点作用。

VGA信号的网线(CAT5)传输----利国电子技术文章

利用网线(CAT5或CAT6等)传输VGA信号有几个优点:1.由于在传输过程中信号是利用平衡方式传输的,因此能根本解决设备之间不共地产生的低频干扰或击穿设备的问题,这在工程现场中是常见但难处理的问题;2.施工过程中走线问题得以简化,甚至可在综合布线时一起解决;3.在某些传输距离时,其性价比要优于传统VGA或RGB电缆,一般情况下,其价格也是可接受的,从综合评价上讲,网线传输是有其可用价值的。

网线传输的原理是将R.G.B.H.V信号经过组合后,变为四组信号,利用网线的四对双绞线进行平衡方式的传输。优点主要是利用平衡方式的特点(隔离和抗干扰)。但网线又有其很致命的弱点,即带宽不够,双绞线的幅频特性(传输带宽)一般在100MHZ,这就根本限制了VGA信号(不同分辨率,尤其是高分辨率时)传输的应用范围,但对于分辨率在1024×768(75MHZ左右)或1280×1024(105MHZ左右)以下的信号还是有实用意义的,以本公司所设计的VGAD-1*2L5为例。未补偿时带宽93MHZ左右(100米)最大补偿时为75MHZ(这是由放大器的带宽增益积限定的)。

由于双绞线同时存在幅频特性(带宽)问题和群延时问题,因此与长线驱动器类似,要作幅频持性与群延时调整,以补偿传输过程中的变暗,模糊和拖尾现象。利国公司的VGAD-1*2L5有16级调整,在100米时利用1024×768和1280×1024图象进行主观评价,效果是完全可接受的,没有拖尾等现象。由于不同分辨率的信号所占带宽不同,因此不能一概而论网络线传输的距离,比如300米或多少米,在640×480时有可能,如果1600×1200的信号能传50米就不错了,因此我公司产品的指标是给出100米网线时的带宽指标。

网线传输还存在另一个问题,就是不等长问题,由于CAT5等网线在生产时考虑到网络信号的同频干扰,故意在生产时将各对线之间长度作成非等长的(有1%左右的长度差)这种结构在VGA信号传输时就造成了R.G.B信号到达的时间不一致,画面会出现分色。如果用专用的等长网线,对工程施工造成很大麻烦,并使网线传输的优点大打折扣,因此一般都采取长度补偿的办法,即对各组线进行长度补偿。但按1%进行补偿,在长距离时补偿线会很长,因此VGAD-1*2L5中设计了分段补偿,即采用内部补偿加外部补偿,可缩短外部补偿线的长度。以我公司产品的经验,100米网线,补偿线分别为20cm—50cm左右,这在工程中是完全可以接受。

VGAD-1*2L5功能介绍:

1. 幅频持性及群延时特性补偿调整,幅频特性调整:16级,无补偿时100米网线带宽,93MHZ,
最大补偿时为75MHZ;
2. 允许对H、V极性进行调整;
3. 长度补偿:内置三段补偿,分别对60—100m,100—150m及150—220m进行补偿,利用内置各段
补偿同时,外部补偿最大≤0.5m。

TOP

STP

RGBHV over shielded Cat 5 success!

I am currently typing this message using a 25ft shielded cat 5 Ethernet cable. The image is extremely clear noticeably better than my 30 foot bundled coax that I normally use. To make the test more difficult, the Cat 5 cable is actually two separate pieces with a junction box 6 feet away from my monitor. This will be the cable that I will use as my HT redesign reaches final completion.

The idea actually came from Thumper. Dismayed by the price of plenum or standard rated coax cable and video amplifiers for his installed, he started tinkering with the idea of using Ethernet cable to run his video signals. He shared his success with me

He told me that I could get good results with standard Cat 5E cable and outstanding results with shielded Cat 5.

Well, premade shielded Cat 5 cables are a little hard to come by so I first tried the experiment using unshielded cat 5. I bought a 25 footer cut it into two 6 foot and 19 foot section and put an HD-15 on each of the cut ends. I then put an in-line Ethernet splicer to join the two Ethernet ends (explain latter). This yielded a long HD-15 to HD-15 cable.

Well the results with this cable where far from stunning. I got plenty of ringing and blurring at most frequencies including really bad results at 60 Hz.

I explained my results to Thumper and he told me to redo it with shielded Cat 5. I was very skeptical because I wasn't having a noise problem but ringing (i.e. impedance mismatch) problem instead.

That's when it hit me; general Cat 5 is 100 ohm twisted pair; however, with the shield tied to ground on the shielded version this would help lower the impedance to closer to video's 75 ohm requirement. I decided to give it another try.

The construction details:

The only local place I could find shielded Cat 5 products was at Fry's. L-com has them but they are mail order and a little more expensive.

I did the exact same thing as before. I bought a 25 foot shielded cat 5 cable and cut it into a 6 foot and 19 foot piece. I also bought a shielded Cat 5 junction box, two HD-15 male solder cup plugs and to 9-pin metal hoods (HD-15 is the same size). I wired the HD-15's in the following fashion to the shielded cat 5 cable.

HD-15 pin Cat 5 color
-------------------------
1. Red + Orange
2. Green + Green
3. Blue + Blue
4.
5.
6. Red - (aka GND) Orange stripe
7. Green - (GND) Green stripe
8. Blue - (GND) Blue stripe
9.
10. Ground (GND) shield wire.
11.
12.
13. H sync Brown
14. V sync Brown stripe
15.

The "-" signals are actually the very same ground as "Ground" is. The H and V don't need their own separate ground line. The results were excellent as I stated before.

At this point you might be saying cool but what does shielded Cat 5 give me over bundled coax? It gives a few things:

1. Thinner form factor.
2. Cheaper cable. Plenum being much cheaper
3. Much easier to solder to an HD-15 connector. Bundled coax requires shield terminators when soldering and big mouth back shells to allow the larger diameter of the cable to exit.
4. similarly, no break-out BNC to HD-15 cables required. These bring their own problems

and my favorite,

5. It allows me to manually switch four RGB sources between 2 displays. This would normally require a matrix switcher which is usually $1000+. To do this, I have two Ethernet jacks (one for my UP-1100 and one for my Princeton Graphics monitor) and four cables (HTPC, AccessDTV, Digital cable and Dreamcast) that go in in any configuration that I want.

All of this with an outstanding video quality to boot. This is really cool.

Thanks Thumper,

-Mr. Wigggles

------------------
The Mothership is now boarding.

[This message has been edited by MrWigggles (edited 06-12-2001).]

TOP

發新話題